Note that this reflects the use of Santiago's effective hard edge model, so the strengths of quads and solenoid need be divided by some factor (in the magnet table) to get the peak strengths, e.g. for use with the full profile in WARP.  Note also that the strengths quoted are for matching the 23.5 mA beam.  For matched settings for other beams, see the Matching Settings table.

! Define Magnets
! Focusing quads (-ve for electrons)
NQF:    QUADRUPOLE,L=0.05164,K1=-161.02
YQF:    QUADRUPOLE,L=0.0745,K1=-121.30

! De-Focusing quads (+ve for electrons)
NQD:    QUADRUPOLE,L=0.05164,K1=161.02
YQDR:   QUADRUPOLE,L=0.0745,K1=129.35
YQDI:   QUADRUPOLE,L=0.0745,K1=129.35

! Note that YQDR (ring) and YQDI (injector) is off-centered and tilted in the horizontal plane
EALIGN,YQDR,DX=0.01389,DTHETA=-0.174533,DS=-0.00123413
EALIGN,YQDI,DX=-0.01389,DTHETA=0.174533,DS=-0.00123413


! Dipoles: Bending, Pulsed, Short, and small/large Flange Dipoles
BD:     RBEND,L=0.0386,ANGLE=0.174533,FINT=0.45
PD:     RBEND,L=0.0518,ANGLE=0.10472,FINT=0.45
SD:     HKICKER
F1D:    KICKER
F2D:    VKICKER
F2DD:   KICKER

!
! How to model the Helmholtz coils and the Earth Field???
!

! Diagnostics: Current Monitor, Phosphor Screen, and Beam Position Monitors
CM:     MONITOR,L=0.0
PS:     MONITOR,L=0.0
BPM:    MONITOR,L=0.05

NSEC: SEQUENCE
    VK:     F2D,    AT=0.0
    Q1:     NQD,    AT=0.08
    B1:     BD,     AT=0.16
    Q2:     NQF,    AT=0.24
    M1:     PS,     AT=0.293
    M2:     BPM,    AT=0.32
    Q3:     NQD,    AT=0.40
    B2:     BD,     AT=0.48
    Q4:     NQF,    AT=0.56
    ENDM:   MARKER, AT=0.64
ENDSEQUENCE

! Special Sections, Induction Gaps and Y
ISEC: SEQUENCE
    VK:     F2D,    AT=0.0
    Q1:     NQD,    AT=0.08
    B1:     BD,     AT=0.16
    Q2:     NQF,    AT=0.24
    Q3:     NQD,    AT=0.40
    B2:     BD,     AT=0.48
    Q4:     NQF,    AT=0.56
    ENDM:   MARKER, AT=0.64
ENDSEQUENCE

YSEC: SEQUENCE
    VK:     F2D,    AT=0.0
    Q1:     NQD,    AT=0.08
    B1:     BD,     AT=0.16
    Q2:     NQF,    AT=0.24
    S1:     SD,     AT=0.271,KICK=-0.03491
    Q3:     YQDR,   AT=0.40
    B2:     PD,     AT=0.48
    Q4:     YQF,    AT=0.56
    ENDM:   MARKER, AT=0.64
ENDSEQUENCE

! Finally, Define the Beamline
UMER:   LINE=(3*NSEC, ISEC, 5*NSEC, ISEC, 5*NSEC, ISEC, NSEC, YSEC)
        USE,UMER